#include

const byte ROWS = 4; //four rows
const byte COLS = 3; //three columns
char keys[ROWS][COLS] = {
  {'1','2','3'},
  {'4','5','6'},
  {'7','8','9'},
  {'#','0','*'}
};
byte rowPins[ROWS] = {5, 4, 3, 2}; //connect to the row pinouts of the keypad
byte colPins[COLS] = {8, 7, 6}; //connect to the column pinouts of the keypad

Keypad keypad = Keypad( makeKeymap(keys), rowPins, colPins, ROWS, COLS );

void setup(){
  Serial.begin(9600);
}

void loop(){
  char key = keypad.getKey();

  if (key != NO_KEY){
    Serial.println(key);
  }
}

/*
|| Written by Dougie Kinnear November 2012
|| building on Nathan Sobieck’s|| Simple Password Entry Using Matrix Keypad
|| 4/5/2012 Updates Nathan Sobieck: Denne e-postadressen er beskyttet mot programmer som samler e-postadresser. Du må aktivere javaskript for å kunne se den.|| I used a Textstar LCD for visul output. The code may need changed
|| for other LCD’s. Control codes may also appear in the
|| serial monitor. See the Textstar data sheet for control codes|| This sketch is discussed on my blog
|| http://www.digitalmaker.co.uk/86/ ‎
|| look under the tags PIN, Textstar, Keypad
|| Please get in touch with any comments, suggestions etc.|| Many thanks to Nathan for sharing his work
*/
// # is to validate password/////////////////////////////////////////////////////////////////#include //http://www.arduino.cc/playground/uploads/Code/Password.zip
#include //http://www.arduino.cc/playground/uploads/Code/Keypad.zipint greenled(11);
int redled(12);//———————- Keypad set up/mapping —————————Password password = Password(“1234”); // Set the password hereconst byte ROWS = 4; // Four rows
const byte COLS = 3; // columns
char keys[ROWS][COLS] = {
{‘1′,’2′,’3’},
{‘4′,’5′,’6’},
{‘7′,’8′,’9’},
{‘*’,’0′,’#’}
};byte rowPins[ROWS] = { 8,7,6,5}; // Assign board pins to keypad rows
byte colPins[COLS] = { 4,3,2}; // Assign board pins to keypad columnsKeypad keypad = Keypad( makeKeymap(keys), rowPins, colPins, ROWS, COLS );
//———————————————————void setup(){
{ 
pinMode(11, OUTPUT); //green light
pinMode(12, OUTPUT); //red light
Serial.begin(9600);
}

keypad.addEventListener(keypadEvent); //add an event listener for this keypaddelay(100); // A further delay to allow the LCD to initialiseSerial.write(254); // Tell LCD multiple command characters are coming
Serial.write(67); // Send a ‘C’ = Cursor set up command
Serial.write(4); // Set cursor to flashing underlinedigitalWrite(12, HIGH); // red LED on
delay(2000); // The LCD should be ready now – these delays can be alteredSerial.write(12); // This is a command to clear the screen and set the cursor to Line 1 column 1
Serial.println(“Enter a PIN then”); // Print the text to the screen
Serial.println(“press ‘#'”); // Print the text to the screen}void loop(){
keypad.getKey();
} void keypadEvent(KeypadEvent eKey){ // This is what happens during a keypad eventswitch (keypad.getState()){
case PRESSED:

Serial.print(eKey); // When a key is pressed * is printedswitch (eKey){

case ‘#’: checkPassword(); break; // press # to check entry
default: password.append(eKey);
}
}
}void checkPassword(){

if (password.evaluate()){ // If it’s correct do this

Serial.write(12);
Serial.println(“CORRECT”);
digitalWrite(12, LOW);
digitalWrite(11, HIGH);

delay(3000);

digitalWrite(11, LOW);
digitalWrite(12, HIGH); 
password.reset(); // reset for next event

Serial.println(“Enter a PIN then”); // Print the text to the screen
Serial.println(“press ‘#'”); // Print the text to the screen

}

else{

Serial.write(12); // If it’s wrong do this

Serial.println(“INCORRECT”);
Serial.println(“TRY AGAIN”);

delay(50); // flash the red LED
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50);
digitalWrite(12, HIGH);
delay(50);
digitalWrite(12,LOW);
delay(50); // stop flashing the red LED

digitalWrite(12, HIGH);
password.reset(); // reset for next event

delay(2500);

Serial.println(“Enter a PIN then”); // Print the text to the screen
Serial.println(“press ‘#'”); // Print the text to the screen}
}